• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

How to Fix a Loose Door Hinge

Fixing a loose door hinge can be a manageable task for the majority of homeowners. If the holes for screws are shattered and do not hold screws, you may require dowels and wood glue to fix the hinge.

Before you do this, however, brush away surface rust. This will aid in keeping the dowels in their place and provide a solid foundation for them to grip onto.

Take the Hinges off

Many standard door hinges can be removed, which makes it easier to move the door from one side to another or to remove the entire door off of the frame should it be needed. Anyone with a little patience can remove the hinges but you need to know what to do.

If the hinges have been painted it is necessary to remove it prior to trying to remove the pins. If you don't, the paint could be smashed off and scratch the door when you attempt to lift it. To break the paint seal put the hinges into an stainless steel pan and fill the pan with water until the hinges are completely submerged. Let the hinges rest in the pan for about 30 minutes. The heat from the water should soften the paint and make it easier to remove the pins.

Once the pins are loosened then you can remove the hinges from the frame and door. You can use a screwdriver to get the job done, but it is recommended that you employ a magnetic screwdriver to complete this project. This type of screwdriver is designed to remove screws made of metal and can make the work go much faster.

Before you attempt to remove the hinges, it is a good idea to spray them with a oil. A simple lubricant will help you to move the process along faster and also remove the pins and screws with ease. You can find this kind of lubricant at most hardware and home improvement stores.

The number of hinges needed will also vary depending on the kind of door you have, and how to fix a window hinge it is set up. Solid-cored and heavier doors will require more hinges, whereas hollow-cored and lighter doors might only need two or three.

Understanding the various types of hinges can help you determine which one is suitable for your needs. The hinges on the exterior are designed to withstand the weight of a door, whereas hinges for interior use must be able support lighter loads.

Reattaching the Hinges

Over time, the hinges of doors may loosen and begin to sag or hang crookedly. This can cause problems however, it's usually simple to repair. A simple tightening can resolve the issue. If the screw holes have been stripped out, it may be difficult to do. Fortunately, there is a trick to make these holes tight again that utilizes a wood dowel.

Begin by drilling the hole with a drill bit close to the new screw size (normally 3/8"). Then, you can use a wood glue and a wooden dowel to fill the hole. To ensure a tight fit, the dowel must be cut to the same length as the screw. Reinstall the screw, and tighten to desired tightness. If the door is still unable to be bounded up, insert a second dowel to the gap. Repeat the procedure. Be sure to shut the door slowly in order to verify the clearances at the perimeter after each adjustment.

Another option is to just use the wood plug instead of dowel. This will work as well however it may take some time to put in. Simply whittle a piece of wood that is the appropriate size for a comfortable fit, and then insert it into the hole. If you don't have a woodworking instrument, you can use toothpicks or matchsticks made of wood.

Make use of a countersink in order to make the hole smaller than the head of screw after you have installed it. This will prevent the screw from hitting the edges of the doors when they are opened and closed. This will make it easier to tighten the screws when installing hinges.

Once you have reinstalled the hinge, make sure to coat it using a dry lubricant to prevent it from getting stuck in the future. You can apply products such as PB Blaster and Liquid Wrench. You should apply a light coat and give it around 15 minutes to fully penetrate the barrel of the hinge.

Refinishing the Hinges

If you're not yet ready to replace your hinges, you can try a few fixes. Make sure the screws that hold the hinge plate to both the door frame and frame are in good condition. If they're loose, tighten them with the help of a screwdriver or a power drill. Be cautious not to tighten the screws to the point that they start to create gaps in the trim joints, or worse remove the threads.

If the issue is that the hinge plates are breaking, you can reattach the plates by applying wood glue to the side of them and inserting wooden dowels or toothpicks in the holes. The dowels or toothpicks serve as a solid base for the screws and help to prevent the plates from shifting when you drive them into position. Allow the glue time to dry before reattaching the hinge.

The screws can also be stripped or missing. This can be fixed by replacing the screws with larger ones. Use a drill bit that is the same size as the screw hole to avoid drilling into the hinge or jamb.

Close the door after you've reattached your hinge and check the gap between the frame and the door. It should be around the thickness of a nickel all the way around or less if there's an existing gap caused by a previous door that hung improperly. This should not be a problem if hinges are properly installed.

If the buy upvc window hinges are still loose, you can add an extra thick hinge between the surface of the hinge plate and the mounting surface. This will give the hinges more space. You can also remove the hinge pin, then pound it down with a hammer in order to tighten it, or install the hinge of a different type. You can also grease your hinges with mineral oil or jojoba in order to reduce friction and hold them in place. Lubricating your hinges periodically will help stop them from becoming stiff and squeaky, and can also prolong their life.

Cleaning the Hinges

The continuous movement of hinges causes friction, which attracts dust particles. These particles can get stuck and accumulate in the moving parts of door hinges, if they're not cleaned and lubricated regularly. The hinge will become stiff and creaky, and its appearance may rapidly deteriorate. Regular cleaning, lubrication, and inspections will ensure the integrity and functionality of hinges that are attached to doors.

Inspect the hinges to see how much rust has formed on their surface. If the rust is so bad that it has damaged the surface of the screw holes or the barrel of the hinge, you'll need to replace them. If you're able to save the hinges, remove any loose rust by using wire brush and steel wool. Then, apply a rust remover from a commercial store or a homemade solution such as lemon juice on the hinge. Allow the rust remover to be on the hinge for a few minutes to dissolve and penetrate any remaining corrosion.

The tightening of screws can restore hinge functionality in the event that you don't want to spend time or money on replacing hinges. If you've stripped the screws, however, it may be necessary to attach an wooden dowel or shim to the upvc window hinge problems. Wooden dowels come in round rods of varying sizes and lengths. You can find them at home improvement stores as well as woodworking supply and craft shops, or online.

You can also make an shim out of metal or plastic depending on the type of hinge you are using. To make a dowel cut a piece made of wooden dowel or another sturdy material to the desired size. You can then dip the dowel into a carpenter's glue and insert it into the cut hole and let the glue hold the dowel in the right position.

Before cleaning the hinges, put down a cloth or towel to protect your flooring from spills. After you have protected the area clean the replacement hinges for upvc windows with a soft sponge or cloth that has been dipped in a mild cleaner to remove dirt and grime. You can also remove tarnish, dirt, and grime. A toothbrush or small brush can be used to reach difficult-to-reach places in crevices and narrow areas.