• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

How to Fix door Hinge a Loose Door Hinge

Repairing a broken door hinge can be a manageable task for most homeowners. But, if the screw holes are damaged and aren't able to hold screws, you might need to use wood glue and dowels before you can install the hinge.

Before you do that though, brush away the surface corrosion. This will help the dowels stay in place and give them a solid foundation to hold onto.

Eliminating the Hinges

Most hinges on doors are removable, which makes it easier to move the door from one side to another or to remove the entire door off of the frame if need be. It is easy for anyone with a bit of patience, though you do need to know how to do it correctly.

If the hinges have been painted it is necessary to remove it before you attempt to remove the pins. If you don't, the paint could be smashed off and scratch your fix door hinge when you try to lift it. Place the hinges into a stainless steel pot and fill it up with water to the point that the hinges are submerged. The hinges should rest in the pan for 30 minutes. The heat from the water should soften the paint and make it easier to remove the pins.

After the pins have been loose, remove the hinges and frame from the door. It is possible to use a regular screwdriver, however it is recommended to use a magnetic screwdriver for this project. This type of screwdriver is designed to grab screws made of metal and will make the project speed up.

Before you attempt to remove the hinges it is recommended to spray them with some grease. A simple lubricant can make the process move along quickly and make it easier to remove the screws and pins. You can find this kind of lubricant at most hardware and home improvement stores.

The number of hinges you need will also depend on what type of door you have, and how it is set up. Heavier doors and solid-core doors will require more hinges while hollow-core doors with a lighter weight might only require two or three.

It is also crucial to understand the different types of hinges so you can determine which ones will be the most effective for your particular situation. The hinges on the exterior are designed to withstand the weight of a door, whereas interior hinges need to be able to support heavier loads.

Reattaching the Hinges

Sometimes, a hinge on a door will loosen over time and start to hang in a crooked manner or sag. It can be a big issue, but the solution is usually easy. A simple tightening can solve the issue. If the screw holes have been ripped out, it could be a challenge to complete. A wood dowel could be used to tighten these holes again.

Start by drilling the hole with a drill bit close to the size of the new screw (normally 3/8"). Then, you can use wood glue and a dowel made of wood to fill in the hole. The dowel should be cut to a length similar to the screw to ensure a snug fit. After that, reinstall the screw and tighten it until the desired degree of tightness. If the door continues to bind up, add another dowel into the gap. Repeat the procedure. Make sure to close the door slowly to examine the clearances around the perimeter after each adjustment.

Another option is to utilize a wood plug instead of a dowel. This is also a viable option however it may take a bit longer to install. Simply whittle a piece of wood to the right size for a snug fit, then press it into the hole. If you don't have a woodworking tool, you can also use toothpicks or wooden matches as well.

Make use of a countersink to make the hole smaller for the head of screw after you have reinstalled it. This will stop the screw from hitting the edge of the doors when they are closed and opened. This will make it easier to tighten the screw after installing the hinge.

After reinstalling the hinge, lubricate the hinge with a dry lubricant. This will prevent it from getting stuck in the future. Products such as PB Blaster or Liquid Wrench are excellent options. You should apply a thin coat and give it about 15 minutes to fully penetrate the hinge barrel.

Refinishing the Hinges

If you're not yet ready to replace your hinges, try a few easy fixes. Make sure the screws that hold the hinge plate to both the door frame and the frame are in good condition. If they're loose, tighten them with the help of a screwdriver or a power drill. Be careful not to tighten the screws so much that they begin to cause gaps at the trim joints, or worse, strip the threads.

If the problem is that the hinge plates are separated from the door and jamb it is possible to reattach them by gluing wood glue to the plate's back and then inserting wooden dowels or toothpicks into the holes. Dowels or toothpicks will provide a solid base for the screws and help keep the plates from moving when you drive them into position. Allow the glue time to dry before reattaching your hinge.

Another common cause of hinges that are loose is that the screws are stripped or gone. This problem can be fixed by replacing the screws. Make sure you use a drill bit that is compatible with the size of the screw hole to avoid drilling into other parts of the hinge or jamb.

Close the door after you've reattached the hinge and measure the gap between the frame and the door. The gap should be the thickness of a penny or less if an older conservatory door hinge replacement was not properly hung. This shouldn't be a problem as long as the hinges are installed correctly.

If you discover that the hinges are loose, try putting an extra thicker shim between the hinge plate and the mounting surface to give a little extra space. You can also remove the hinge pin and pound it down with a powerful hammer in order to tighten it, or install the hinge of a different type. You can also grease your repair window hinges with mineral oil or jojoba to decrease friction and help keep them in position. Regularly lubricating your hinges will help keep them from becoming stiff or squeaky, and can also extend their life.

Cleaning the Hinges

The friction generated by the hinge's constant motion attracts dust particles. These particles can get stuck and accumulate in the moving parts of door hinges, if they're not cleaned and lubricated regularly. As a result the hinge becomes stiff and creaky and its appearance could be damaged quickly. Regular cleaning, lubrication, and inspection can help preserve the quality of door's hinges and ensure their proper operation.

Examine the hinges to determine how much rust has accumulated on their surface. If the rust has corroded to the point of destroying surface of the barrel or screw holes, you will need to replace the hinges. If you are able to save the hinges, begin by brushing off loose rust using steel wool and a wire brush. Apply a commercial rust removal solution or homemade solution like lemon juice to the hinge. Let the rust removal solution be on the hinge for several minutes to penetrate and dissolve any remaining rust.

The tightening of screws can restore hinge functionality in the event that you don't want to spend time or money on repairing hinges. It might be necessary to add a wooden shim or dowel to the hinge in the event that the screws have been stripped. Wooden dowels are round pieces made of wood in the shape of rods that are available in varying lengths and diameters. You can buy them online, at woodworking supply shops and at home improvement stores.

A shim may be made of a piece of metal or plastic, depending on the kind of hinge you've got. To make a dowel cut a dowel from wood to the desired length. You can dip the dowel into the adhesive of a carpenter and place it in the hole. The glue will hold the dowel securely in place.

Before cleaning the hinges, put down a piece of paper cloth or towel to shield your flooring from spills. After the area has been secured, proceed to clean the hinges using a soft cloth or sponge that has been soaked in mild cleaner or vinegar to remove built-up dirt, grime and tarnish. A small brush or toothbrush can be used to access difficult-to-reach spots in crevices or tight spots.