• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

How to Fix a Loose Door Hinge

Most homeowners can fix hinges that are loose. But, if the holes for screws are smashed and aren't able to hold screws, you may need to use wood glue and dowels before you can put back the hinge.

Before you do that, however you should clean off any surface corrosion. This will help the dowels remain in place and provide them a solid base to grip into.

Eliminating the Hinges

Most hinges on doors can be removed, which makes it easier to move the door from one side to the next or take the entire door off the frame should it be needed. Anyone who is patient can remove the hinges, but you need to know what to do.

If the hinges are painted, you'll need to get rid of the paint prior to trying to remove the pins. You could scratch your door if do not remove the paint. To break the seal, place the hinges in a stainless steel pan and fill the pan with water until the hinges are fully submerged. Let the hinges sit in the pan for 30 minutes. The heat of the water will soften the paint, making it easier to take off.

Once the pins are removed, take the hinges and the frame from the door. You can use a screwdriver to get the job done, however it is recommended that you make use of a magnetic screwdriver for this project. This type of screwdriver is designed to pick up screws made of steel and can make the work run much more quickly.

Before you attempt to remove the hinges it is recommended to spray them with some grease. A simple lubricant will help the process go by more quickly and help you remove the screws and pins. You can purchase this kind of lubricant at most hardware and home improvement stores.

The number of hinges required will also vary depending on the kind of door you have and how it's set up. Doors with solid cores and heavy weights will require more hinges, whereas hollow-cored and lighter doors might only require two or three hinges.

It is also essential to be aware of the various kinds of hinges so you can determine which ones best suit your needs. Exterior hinges are typically designed to support the door's weight, while interior hinges will need to be able to handle lighter loads.

Reattaching the Hinges

Over time, the hinges of doors may lose its grip and then begin to slide or hang crookedly. It could be a huge problem, but the fix is usually easy. Retightening the screw will typically solve the problem. However when the screw holes are stripped out, it can be more difficult to accomplish. A wood dowel can be used to tighten the holes once more.

Begin by drilling the old hole using a drill bit close to the new screw size (normally 3/8"). Fill in the hole using wood glue and a wooden stick. The dowel should be cut to a length that is similar to the screw to ensure a tight fit. After that, reinstall the screw and tighten it to the desired degree of tightness. If the door has an tendency to get stuck, then add another dowel to the gap and repeat the process. Be sure to close the door slowly in order to examine the clearances around the perimeter after each adjustment.

You can also use a wooden plug in place of the dowel. It works similarly, but it may take a little longer to set up. You can insert the wood piece that has been whittled to the proper size. If you don't have an instrument for woodworking You can use toothpicks or matchsticks made from wood.

Use a countersink to make the hole smaller than the head of screw after you have reinstalled it. This will stop the screw from hitting the edges of the doors when they are closed and opened. This will make it easier to tighten the screw when installing the hinge.

Once you've reinstalled your hinge, be sure to lubricate it with a dry lubricant to ensure that it doesn't get stuck in the future. Products like PB Blaster or Liquid Wrench are excellent alternatives. You should apply a thin coat and wait for approximately 15 minutes to get into the hinge barrel.

Refinishing the Hinges

If you're not yet ready to replace hinges, you could try a few simple fixes. Make sure the screws that secure the hinge plate in place to the door frame and the frame are tight. If they're loose, tighten them using the help of a screwdriver or a power drill. Be careful not to tighten your screws so much that they cause gaps at the trim joints, or even worse remove the threads.

If the issue is that the hinge plates are splitting, you can reattach the plates by applying wood glue to the back of them and then inserting wooden dowels or toothpicks into the holes. Dowels and toothpicks create a solid base for the screws, preventing the plates from shifting as you push them in. Allow the glue to dry before attaching the hinge.

Another reason for loose hinges is that the screws are stripped or gone. You can fix Door hinge this problem by replacing the screws with longer ones. Make sure you use a drill bit that is compatible with the size of the screw hole in order to avoid drilling into other parts of the jamb or window hinge repair cost.

Close the door once you've reattached your hinge and check the gap between the frame and the door. The gap should be about the thickness of a penny all around or less if an old door was not properly hung. This shouldn't be a problem if the hinges are properly installed.

If you find that the hinges are loose, try putting the thicker shim of the hinge between the hinge plate and the mounting surface to add a little extra space. You could also try removing the hinge pin from the problem hinge and then pounding it with a hammer in order to make it tighter or use an entirely new hinge pin. You can also lubricate your hinges using mineral oil or jojoba to reduce friction and keep them in position. Lubricating your hinges periodically can prevent them from becoming stiff and squeaky, and also extend their lifespan.

Cleaning the Hinges

The continuous movement of hinges causes friction, which attracts dust particles. These particles can get stuck and accumulate over time in the moving parts of door hinges if they're not cleaned and lubricated regularly. The hinge will get stiff and creaky and its appearance can rapidly change. Regular cleaning, lubrication and inspections will maintain the functionality and quality of hinges on a door.

Inspect the hinges to see how much rust has accumulated on their surfaces. If the corrosion has reached the point of destroying the surface of the hinge barrel or screw holes, you'll require replacement of the hinges. If you are able to save the hinges, clean any loose rust by using wire brush and steel wool. Then, apply an industrial rust remover or homemade solution like lemon juice on the hinge. Let the solution that removes rust remain on the hinges for a few minutes in order to penetrate and dissolve the remaining rust.

If you don't want to spend money and time replacing window hinges repair, simply tightening the screws can bring back the hinge's functionality. If you've sanded the screws however, it might be necessary to attach an wooden dowel or shim to the double glazing hinge repairs. Dowels made of wood are square pieces of wood that are in the form of rods, which are available in various lengths and diameters. You can find them at home improvement stores, woodworking supply and craft shops, or online.

You can also create an shim using made of plastic or metal depending on the kind of hinge you own. To make a dowel cut a dowel from wood to the desired length. You can then dip the dowel in a carpenter's glue and insert it into the stripped hole, allowing the glue to hold the dowel in the right position.

Before cleaning the hinges, put down a paper towel or cloth to protect your flooring from spills. After the area has been secured, proceed to clean the hinges using a soft sponge or cloth that has been soaked in mild cleaner or vinegar to get rid of built-up dirt, grime and tarnish. A small brush or toothbrush can be used to access difficult-to-reach spots in crevices or tight areas.