• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

How to Replace Window Panes

A damaged window pane can be an issue. This could be an opportunity to upgrade to energy-efficient windows or insulated ones, and reap benefits such as improved comfort, higher resale value and lower utility costs.

It's a task you can tackle yourself at only a fraction of the cost of hiring a professional. It requires the right equipment and an hour or two of your time.

Glass

Replace your single-paned windows using tempered or insulation glass to improve the efficiency of your energy, reduce noise, and protect the original character of your older home. The process of replacing windows is easy and can be completed by most homeowners who possess basic hand tools. In addition to a new pane, the following items are required: latex glazing putty; pliers, glazier's points and the use of a heat gun to warm the old putty, if needed. Before beginning, wear gloves and safety glasses as working with broken glass can cause injuries.

Begin by removing any remaining broken pieces of glass. This is best done using the help of pliers though using a flathead screwdriver can also work in a pinch. Then, use a wooden chisel, or putty knife, to take the remainder of the old putty from around the frame and sash. Be careful not to damage the Replacement Window Near Me sash. Take your time and work slowly. It is best to do this on a stable ladder rather than the ground and to place someone on the sash to help hold it in place.

After you have removed all of the old putty, you can prepare the window frame to fit the new pane. To allow for seasonal expansion or contraction, subtract 1/8 inch each from the measurements of the width and height. Bring these measurements to an hardware store or home center and get a piece of stock glass cut to size. You can cut the glass yourself if you possess the right tools.

After putting in the new pane after installing the new pane, put a tiny amount of caulking along the edge to seal it against weather. Install a glazier's pointing on both sides of the frame. This will help secure the pane. The points shouldn't be too tight that they create friction between the frame and the sash, but they should also not be loose.

Before applying the putty work it in a gentle manner until it's soft and free of lumps. Then you can roll it into pencil-sized strips. The first strip should be glued to the corner of the frame. Work from one corner to another and ensure that it is even and smooth.

Glazier's Points

The glazier's facets are tiny triangular pieces of steel which help to secure glass into a window frame without scratching or damaging the delicate surface. Understanding how to use these hidden little helpers is easy and could save you money on professional installation or the cost of buying new glass.

After the old putty as well as the glazier's points have been removed, thoroughly clean the frame with a knife to get rid of any remaining residue. If needed, lightly sand the wood along the grooves of the rabbet to smooth rough areas. If you sand wood, protect it with painter’s tape to protect it from damage caused by accidental sanding.

Write down the exact dimensions of the frame. These dimensions can be taken to an hardware or home centers store and the new pane will be cut a bit smaller. This will ensure that the pane fits comfortably and allows for expansion and contraction.

Place the new pane in the frame and press it into the frame with your hand. Make use of the chisel's point or the back of the putty blade to tap in the glazier's points as shown in Figure 11. The glazier's points should be flush against the top edge of your pane and the shoulders should be just below that lip.

Apply a thin layer glazing compound on the rabbet grooves and edges of new glass. This will seal and protect the edges. Allow it to dry and cure fully.

Install the new window sash after the glazing compound has dried. First, coat the wood with a thick layer of linseed. This will keep the new putty from sucking up the moisture and deteriorating and cracking over time. Apply the coating using a brush this coat, or even the tip of the blade. Then use the chisel on the back of the tool or the back of the putty handle to gently smash the new sash or glazier's point into grooves of the rabbet. Repeat this process every 10 inches around the frame's perimeter.

Putty

A baseball hit or a rock thrown by error, or a tree falling can result in a cracked or cracked window pane. Luckily, most windows can be replaced by simply placing a new piece of glass in its the right place. The glass is held in place by a small metal clip called a glazier's point, and putty, also called glazing compound. Remove the old pane and clean the area using the rag, a pull-type scraper or wood chisel. Wear safety glasses and gloves while doing this work. If the window is glued to the frame, you'll have to use a heat gun to soften the adhesive prior to cutting it loose.

If you are planning to install your original sash, you must remove the molding that supports the old pane. Sand the sash until it is flat and ready for new caulk. Once the sash is reinstalled then, you can apply a silicone caulk over the glass. This will ensure that it won't be leaking or fade over time.

Take the glazing points out of the rabbets and the grooves in the sash where the glass is. If they are hard to chisel, use an instrument such as a heatgun over them for a few minutes to soften them. If you're using a heat gun, make sure not to scratch the railings of the sash or the sash itself by holding the tool too close.

Prepare a bed for your new pane by removing the old putty and glazing points. Roll a rope of glazing compound between your hands, and form it to be about 1/2-inch thick. Place it into the rabbets, where the glass will be placed. The glass must be positioned against the putty on both sides. If needed you want to tap your glass lightly into the rabbet using your thumb.

If the new pane is cracked then you can seal it with a solvent-based glue or silicone caulk prior pressing it into the sash. If not, you'll have to putty over the crack to form a tight seal and keep water out. After the putty has dried remove the oily film off of the glass and let it dry completely before painting. If you paint before the putty is fully dry, it won't create an effective seal and could discolor or leak in time.

Paint

If you've suffered a break in a window panes replacement pane, you might be concerned about the expense of a new one. It's true that replacing a single pane glass doesn't need to be expensive if you do it on your own. Even a replacement double glazed windows-paned window could be replaced at a fraction of the cost it costs for a professional.

If you are working with large glass windows, first make sure it is securely fixed to the frame. With the right tools and techniques, you can make this task relatively easy and quick.

When you are ready to start with the removal of the window replacements near me pane. Remove the glazing points made of metal that are attached to it. These are tiny triangles of metal that act as "nails" that hold the window within the frame. They are submerged under a bead of glazing putty that hardens into a solid, molded wedge that secures the window in place and hides the window's points.

After you have removed the old pane removed Clean up the frame and wood. Scrape off any old paint, and sand the rabbet grooves where the glazing points were placed. Sand them to bare wooden surfaces so you can paint the frames the same color. After sanding the wood you can apply a layer flax oil. This will help to prolong the life of the frame.

Then, you need to measure the size of the window's opening. You'll need to take vertical and horizontal measurements of the entire opening, and also the thickness of the old pane. To determine the exact dimensions of the new pane, subtract 1/8 inch from both measurements. This will also allow for expansion and contraction of the glass during seasonal changes. You can take these measurements to a hardware or home improvement shop and have the glass cut for you.

Now, it's time to bed the new window pane. To do this, place the pane inside the frame and move it around until a 1/16 inch of putty remains between the edge of the glass and the sash on all four sides. Use a putty knife to smear the putty evenly, making sure that there isn't an excessive amount of excess putty in the corners and along the edges. When the putty dries, it can be painted with the same color as the frame to prevent water and air from leaking into the frame and causing fogging.