• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

How to Fix Door Hinge a Loose Door Hinge

Fixing a door hinge that is loose can be a manageable task for most homeowners. But, if the holes for screws are smashed and won't hold screws you may need to put in wood glue and dowels before you can reinstall the hinge.

Before you do this, however you should clean off any surface corrosion. This will help the dowels remain in place and provide them a solid base to grip into.

Eliminating the Hinges

Many standard door hinges are able to be removed, making it easier to move the door from one side to the other or take the entire door off of the frame should it be needed. The removal of the hinges is simple for anyone with patience, though you do need to know how to do it right.

If the hinges are painted, you'll need to take off the paint prior to attempting to remove the pins. If you don't, the paint could flake off and scratch your door when you try to lift it. Put the hinges in the stainless steel pot and fill it up with water to the point that the hinges are submerged. The hinges should remain in the pan for about 30 minutes. The heat of the water will soften the paint, making it easier to take off.

After the pins are loosening then you can remove the hinges from the frame and door. You can employ a screwdriver for the job done, but it is recommended to make use of a magnetic screwdriver for this project. This type of screwdriver is specially designed to pick up metal screws and will aid you in getting the job accomplished much faster.

It is a good idea to spray lubricant on the hinges before attempting to remove them. A simple lubricant will help the process move along quickly and help you remove the screws and pins. This type of lubricant can be found at most hardware stores as well as home improvement shops.

It is important to keep in mind that the number of door hinges you'll require will vary depending on the type of upvc door hinge replacement and its configurations. Heavier and solid-cored doors will require more hinges while hollow-cored and lighter doors might only require two or three hinges.

It is also crucial to know the various types of hinges so you can determine which ones best suit your needs. Exterior hinges are typically designed to support the door's weight, while interior hinges will have to be able to handle lighter loads.

Reattaching the Hinges

Over time, the hinges of doors may loosen and begin to hang crooked or sag. This can cause problems but is usually easy to repair. In most cases, a simple retightening of the screw will solve the problem. However when the screw holes have been stripped out, this can be more difficult to accomplish. A wood dowel could be used to tighten these holes again.

Start by drilling out the old hole using a drill bit that is close to the size of the new screw (typically 3/8"). Fill in the hole using wood glue and a wooden stick. The dowel should be cut to a length exactly the same as the screw to ensure a secure fit. After that, reinstall the screw and tighten it until the desired level of tightness. If the door continues to have an tendency to get stuck, then add another dowel to the gap and repeat the process. Close the door slowly after each adjustment to ensure that the clearances around the perimeter are correct.

You could also use a wood plug instead of the dowel. It will work just as well but might take a little longer to set up. Simply whittle a chunk of wood to the proper size to ensure a secure fit, and then insert it into the hole. If you don't own an instrument for woodworking, you can use toothpicks or wooden matchsticks.

After you have reinstalled the new screw, use a countersink bit to make the hole for the head of the screw smaller, so that it doesn't touch the edge of the door when it's opened and closed. This will make it much easier to tighten the screws when reinstalling hinges.

Once you have reinstalled the hinge repair plate, be sure to coat it using a dry lubricant to ensure that it doesn't get stuck in the future. You can use products such as PB Blaster and Liquid Wrench. Apply a thin coat and give it around 15 minutes to fully get into the hinge barrel.

Refinishing the Hinges

If you are not ready to replace the hinges on your door, you can do a few simple repairs. The first step is to make sure that the screws securing the hinge plate to the frame and door are tight. If they're loose, tighten them using an electric drill or screwdriver. Be cautious not to over tighten the screws as this can cause gaps to form at the trim joints, or more seriously, tear out the threads.

If the problem is that the hinge plates are separating from the door and jamb it is possible to reattach them by gluing wood glue to the back of the plates, and then inserting toothpicks or wooden dowels into the holes. The toothpicks or dowels will give a solid foundation for the screws and help prevent the plates from shifting when you drive them into position. Allow the glue to dry before reattaching the window hinge repair cost.

Another common cause of loose hinges is that screws are worn out or gone. This issue can be resolved by replacing the screws. Use a drill bit that is similar to the size of the screw hole to avoid drilling into the hinge or jamb.

Close the door once you have reattached your hinge and check the gap between the frame and the door. The gap should be the thickness of a penny or less if an older door was not properly hung. If the hinges were installed properly, this shouldn't be an issue.

If the hinges still seem loose, you could add a stronger hinge between the hinge plate surface and the mounting surface. This will give the hinges more space. You can also take off the hinge pin and pound it down with a powerful hammer in order to tighten it, or install a new hinge. You can also lubricate your hinges with mineral or Jojoba oil to decrease friction and assist in keeping their place. Periodically lubricating your hinges can aid in keeping them from becoming stiff or squeaky and will also extend their life.

Cleaning the Hinges

The friction caused by the hinge's constant motion attracts dust particles. Without periodic cleaning and lubrication, these particles get stuck in the moving parts of a door hinge and accumulate over time. The hinge will become stiff and creaky and its appearance may rapidly deteriorate. Regular cleaning, lubrication and inspection can help preserve the integrity of a door's hinges and ensure their proper function.

Check the hinges for rust accumulation. If the rust has corroded to the point of destroying surface of the hinge barrel or screw holes, you will have to replace the hinges. If you're able to save the hinges, clean any loose rust with a wire brush and steel wool. Then, apply an industrial rust remover or a homemade solution such as lemon juice to the hinge. Allow the rust remover to be on the hinge for several minutes to dissolve and penetrate any remaining rust.

The tightening of screws can restore hinge function If you don't wish to spend money or time on replacing hinges. If you have stripped the screws, however, it may be necessary to attach a wooden dowel or shim to the hinge. Dowels made of wood are available in round rods that vary in lengths and sizes. You can purchase them online, in woodworking supply shops and home improvement centers.

You can also make a shim from a piece metal or plastic depending on the kind of hinge you have. To make a dowel, you need to cut a dowel from wood to the desired length. You can then dip the dowel into a carpenter's glue and insert it into the hole that you have stripped and let the glue hold the dowel in the right position.

Before you start cleaning the hinges, put down a paper or cloth towel to shield floors and other surfaces from accidental spills and drips. After protecting the area then clean the hinges using an easy sponge or cloth that has been dipped in mild cleaner to get rid of dirt and grime. You can also remove tarnish, dirt, and grime. You can use a toothbrush or small brush to reach difficult-to-reach places in crevices and tight areas.