• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

How to fix door Hinge a Loose Door Hinge

Most homeowners can repair hinges that are loose. But, if the screw holes are damaged and can't hold screws, you may need to put in wood glue and dowels before you can put back the hinge.

Clean up any surface rust. This will help the dowels remain in place and provide them a solid base to rest on.

Take the Hinges off

Many standard door hinges can be removed, which makes it easier to move the door from one side to another or take the entire door off of the frame, if needed. The removal of the hinges is easy for anyone with a bit of patience, though you do need to know how do it correctly.

If the hinges have been painted you'll need to take off the paint before you attempt to remove the pins. You may scratch your door if you do not remove the paint. To break the seal put the hinges in a stainless steel dish and fill the pan with water until the hinges are fully submerged. Allow the hinges to sit in the pan for around 30 minutes. The heat from the water should soften the paint and make it easier to get rid of the pins.

After the pins have been loosen, you can remove the hinges from the door and frame. It is possible to use a standard screwdriver, however a magnetic screwdriver is recommended for this task. This type of screwdriver is designed to pick up screws made of steel and can make the work run much more quickly.

Before you attempt to remove the hinges it is recommended to spray them with lubricant. A simple lubricant can make the process move along quickly and aid in the removal of the pins and screws. You can find this type of lubricant at most hardware and home improvement stores.

You should also keep in mind that the number of door hinges you'll require will differ based on the fix door hinge's type and its setting. Heavier doors and solid-core doors will require more hinges, while hollow-core doors with a lighter weight may only require two or three.

It is also essential to be aware of the various kinds of hinges to determine which ones will work best in your situation. Exterior upvc hinges are generally designed to support the weight of the door and interior hinges require to handle lighter loads.

Reattaching the Hinges

Over time, a door hinge can loosen and begin to hang crooked or sag. This can be a major issue, but the solution is usually quite simple. Most of the time, a simple retightening of the screw will solve the problem. However, if the screw holes are stripped out, this may be more difficult to do. Fortunately, there is a method to make these holes tight again that uses a wood dowel.

Start by drilling out the old hole using a drill bit that is similar to the size of the new screw (typically 3/8"). Then, use a wood glue and a wooden dowel to fill the hole. The dowel should be cut to a length exactly the same as the screw to ensure a tight fit. Then, reinstall the screw and tighten it until the desired level of tightness. If the door continues to bind up, you can insert another dowel to the gap. Repeat the process. Be sure to shut the door slowly to check the perimeter clearances after each adjustment.

You could also use a wood plug instead of the dowel. This will work similarly, but it may take a bit longer to install. You can use the wood piece that has been whittled to the proper size. If you don't have a wooden tool You can also try using toothpicks or wooden matches as well.

Use a countersink to make the hole smaller for the head of screw after you have put it back in place. This will stop the screw from hitting the edge of the doors when they are closed and opened. This will make it easier to tighten the screws after installing hinges.

Once you've reinstalled your hinge, be sure to grease it with a dry lubricant to help keep it from getting stuck in the future. You can use products like PB Blaster and Liquid Wrench. Apply a thin coat and wait for about 15 minutes to fully reach the barrel of the hinge.

Refinishing the Hinges

If you're not ready to replace hinges, you could try a few simple fixes. Make sure the screws that secure the hinge plate in place to the door frame and frame are in good condition. If they're loose, tighten them using a screwdriver or power drill. Be careful not too tighten the screws as this can cause gaps to form at the trim joints or worse, strip out the threads.

If the issue is that the hinge plates are separated from the door and jamb it is possible to reattach the hinges by applying wood glue to the plate's back and then inserting wooden dowels or toothpicks into the holes. Dowels or toothpicks will provide a solid base for the screws and help keep the plates from moving when you drive them into place. Let the glue dry before you can reattach your hinge.

Another common cause of loose hinges is that the screws are stripped or gone. This can be corrected by replacing the screws. Make sure you use a drill bit that matches the size of the screw hole in order to avoid drilling into other parts of the hinge or jamb.

After you've reattached your hinge close the door and examine the gap between the frame and the door. The gap should be about the thickness of a penny or less if the old door was not hung correctly. If the hinges were put in place correctly, this shouldn't be a problem.

If you discover that the hinges remain loose, try adding the thicker shim of the hinge between the hinge plate and the mounting surface to give an extra inch of space. You could also try taking the hinge pin from the troublesome hinge and pounding it with a hammer in order to make it tighter or use the hinge pin from a different angle altogether. You can also lubricate your hinges with mineral or jojoba oil to lessen friction and aid in holding their position. Periodically lubricating your hinges can aid in keeping them from becoming stiff or squeaky and can also extend their life.

Cleaning the Hinges

The friction created by the constant movement of a hinge attracts dust particles. These particles can get stuck and build up in the moving parts of door hinges, if they're not maintained and cleaned regularly. The hinge will get stiff and creaky and its appearance could rapidly diminish. Regular cleaning, lubrication and inspection can help preserve the quality of a hinged door and ensure their proper function.

Examine the hinges for signs of rust accumulation. If the corrosion has reached the point of damaging the surface of the barrel or screw holes, you'll need to replace the hinges. If you can save the hinges, you should first clean off loose rust using steel wool and a wire brush. Then, apply a rust remover from a commercial store or a homemade solution such as lemon juice to the hinge. Let the rust removal solution sit on the hinge for several minutes to dissolve and penetrate any remaining rust.

Retightening screws can restore hinge functionality If you don't wish to spend money or time to replace hinges. It is possible to attach dowel or shim made of wood to the hinge in the event that the screws have been degraded. Wooden dowels are round pieces of wood that are in the form of rods which are available in varying lengths and diameters. They are available at home improvement centers as well as woodworking supply and craft shops, or on the internet.

A shim could be made of metal or plastic, depending on the kind of hinge you've got. To make a dowel, you need to cut a dowel from wood to the desired length. You can then dip a dowel in carpenter's glue handles and hinges insert it in the hole. The glue will secure the dowel in place.

Before you start cleaning the hinges, put down a cloth or paper towel to shield flooring and other surfaces from accidental spills and drips. After securing the area, clean the hinges using a soft sponge or a cloth dipped into mild cleaner to get rid of dirt, grime, and tarnish. You can make use of a toothbrush or a small brush to reach difficult-to-reach places in crevices or tight areas.